Nice TTPRO BD, Инструкции и предупреждения по установке и использованию

Страница: 5 / 80

English – 4
EN
3.3 - ON/OFF button
SWITCHING ON/OFF AND MOTOR SEARCH
3.3.1 - Switching On of TTPRO BD
01.
Press and release the ON/OFF button (

1 beep);
scanning of the motors starts automatically, (at this stage the level LEDs are flash-
ing alternately).
3.3.2 - Searching for the motor
3.3.2.A - TTPRO BD connected via TTBUS
01.
If TTPRO BD is connected via TTBUS and a motor is detected, the
OK
led turns
GREEN and the level leds indicate the number of motors detected (1 to 8 with
dim leds), and the currently selected motor (the brightest led). Led A flashes to
indicate that the motors are connected over the TTBUS network.
3.3.2.B - TTPRO BD connected via RADIO BD
(for motors which support the protocol)
01.
If TTPRO BD is connected via RADIO BD (for enabled motors) and a motor is de-
tected, the OK led flashes GREEN and the level leds indicate the number of mo-
tors detected (1 to 8 with dim leds), and the currently selected motor (the brightest
led). Led A is off to indicate that the motors are connected via RADIO BD.
02.
The detected motor will make two brief movements to confirm it is attempting to
connect. Us key
(or key ) to select another motor, if so desired. Press
key
to make the motor make two brief movements and thus confirm you have
selected the right one. Press
OK
to confirm. The
OK
led will flash
GREEN
and
TTPRO BD will wait for you to:
- press a key on a remote control (a paired one is detected)
- enter the motor's 4 digit password (if no remote control is paired).
03.a
Press a remote control key: TTPRO BD waits for you to press a key on a remote
control which is very close to TTPRO BD and already paired with the motor (the
led
DRY
CONT.
flashes). Press
RADIO
TEST
to return to motor selection. When you press a key on
a remote control which is already paired with the motor, the OK led turns GREEN
to indicate that the selected motor is now connected.
03.b
Enter Password: if you do not have a remote control paired with the motor, you
must enter the motor's password. Use key
(or key ) to select the digits
(0 is represented by all numerical leds flashing) and confirm by pressing
OK
. After
you confirm the fourth digit (password complete) access with the entered pass-
word is requested. If the password is valid the OK led turns GREEN to indicate
that the motor is connected, otherwise it turns steady RED .
Only a limited number of attempts to access the motor are permitted (the number
of attempts depends on the motor itself).
3.2 - Function and description of the LEDs
CONNECTION LEDS DESCRIPTION
OK
2
3
1
RED (1)
• LED on permanently:
- no motor connected.
- there have been serious errors of communica-
tion and TTPRO BD did not recognise the motor
properly.
RED (2)
• LED flashes slowly: motor search procedure
under way.
•
LED flashes fast: storing of motor parameters or
transmitters under way
GREEN (3)
• LED on permanently: motor connected and
recognised or procedure terminated successfully.
•
LED flashes slowly: TTPRO BD waits for confir-
mation from the operator (pressing of the OK button);
after 5 sec the LED stops flashing and the operation
ends unsuccessful.
LED OF FUNCTION DESCRIPTION
STEADY LIGHT Function already present and already set.
LIGHT OFF Function not present.
FLASHING LIGHT Function already present but not yet set , or currently being set.
LED OF LEVEL DESCRIPTION
This series of LEDs
can have different
meanings depend-
ing on the function
enabled
• RF noise level (V-METER)
• Motor Address
• Level
• Setting
CHARGE LED DESCRIPTION
Usb If the USB cable is connected , the BLUE LED is on.
Chrg
If the USB cable is connected , the GREEN LED flashes when
the battery is charging.