1
– English
EN
GENERAL WARNINGS:
SAFETY - INSTALLATION - USE
(instructions translated from Italian)
WARNING
For personal safety it is important to observe these instructions.
Observe these instructions - improper installation can result in
serious injury.
WARNING
Important safety instructions: keep these instructions.
WARNING
All installation procedures, connections, programming and main-
tenance of the product must be performed exclusively by a quali-
fied technician!
•
Do not open the device protection housing as it contains non-serviceable electrical
circuits.
•
Never apply modifications to any part of the device. Operations other than as specified
can only cause malfunctions. The manufacturer declines all liability for damage caused
by makeshift modifications to the product.
•
Never place the device near sources of heat and never expose it to naked flames. This
may damage it and cause malfunctions.
•
This product is not intended to be used by persons (including children) whose physi-
cal, sensory or mental capabilities are reduced, or who lack the necessary experience
or skill.
•
Make sure that children do not play with the product.
OTHER WARNINGS
•
Also check the instructions contained in the instruction manual of the motor to which
the product is associated.
•
Handle the product carefully, while avoiding crushing, bumping and dropping it so as
to prevent damages to the product.
•
The packing materials of the product must be disposed of in compliance with local
regulations.
GENERAL WARNINGS: SAFETY - INSTALLATION - USE
1
1 - PRODUCT DESCRIPTION AND INTENDED USE
2
2 - ELECTRICAL CONNECTIONS
2
3 - PRODUCT OPERATION
2
3.1 - Function and description of buttons
2
3.1.1 - Buttons for movements
3
3.2 - Function and description of the LEDs
4
3.3 - ON/OFF button
4
3.3.1 - Switching On of TTPRO BD
4
3.3.2 - Motor search
4
3.3.2.A - TTPRO BD connected via TTBUS
4
3.3.2.B - TTPRO BD connected via RADIO BD
4
3.3.3 - Forced motor scan
5
3.3.4 - Switching Off of TTPRO BD
5
3.4 - Transmitter programming
5
3.4.1 - Memorisation of the transmitter
5
3.4.2 - Deleting a single transmitter
5
3.4.3 - Deleting all transmitters
5
3.4.4 - Memorising a single transmitter button (Mode 2)
5
3.4.5 - Deleting a transmitter memorised in Mode 2
5
3.5 - Basic programming
5
3.5.1 - Programming the direction of movement
5
3.5.2 - Programming of positions
6
3.5.2.A - Manual programming of positions “0”, “1” and “I”
6
3.5.2.B - Automatic programming of the positions “0” and “1”
6
3.5.3 - Deleting pre-programmed positions
7
3.6 - Settings/Adjustments
7
3.6.1 - Setting the type of “dry-contact”
7
3.6.2 - Setting the time of duration the maneuver
7
3.6.3 - Setting the speed
8
3.6.4 - Setting the level “soft-start” and “soft-stop”
8
3.6.5 - Setting the level of sensitivity to obstacle / DRC
8
3.7 - Climatic sensors
8
3.7.1 - Setting the intervention level for “wind” protection
8
3.7.2 - Enabling/disabling of climatic sensors
8
3.7.3 - Setting the intervention level for “sun” protection
9
3.7.4 - Setting the direction of rotation of the motor in case of rain
9
3.8 - Insights
9
3.8.1 - Radio test function
9
3.8.2 - Deleting the parameters from the motor
9
3.8.3 - Copying parameters and transmitters
9
3.8.3.1 - Deleting of the parameters stored in TTPRO BD
10
3.8.4 - Checking the software version
10
3.8.5 - Updating the TTPRO BD firmware
10
3.8.6 - Changing the motor address
10
4 - BATTERY REPLACEMENT
10
5 - DISPOSAL OF THE PRODUCT
11
CE DECLARATION OF CONFORMITY
11
CONTENTS
