5
– English
EN
If no motor is found at the end of the search, TTPRO BD emits a brief beep and the
OK
led turns steady
RED
.
3.3.3 - Forced motor scan
01.
Press key
or key
for 1 second to force a scan for motors at the remain-
ing addresses.
02.
You can also change the scan mode (TTBUS - BD) by pressing key
or
for 1 second at the end of each scan.
3.3.4 - Switching Off of TTPRO BD
01.
Press the
ON/OFF
key.
02.
Release the button when TTPRO BD emits 1 beep and the RED LED starts to
flash quickly.
TTPRO BD turns off automatically after 1 minute of inactivity.
3.4 - Transmitter programming
BUTTONS DEDICATED TO TRANSMITTERS
3.4.1 - Memorisation of the transmitter
DRY
CONT.
01.
Press and release the button
DRY
CONT.
: the LED above the button starts blinking slow-
ly, waiting to receive a transmitter.
02.
(within 5 sec) Press and release any button on the transmitter to be memorised:
➔
the LED on the button
DRY
CONT.
flashes quickly.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
3.4.2 - Deleting a single transmitter
01.
Press and release the button
DRY
CONT.
: the LED above the button starts blinking slow-
ly, waiting to receive a transmitter.
02.
Press and release the button
RADIO
TEST
: the button starts blinking slowly waiting for a
transmitter.
03.
(within 5 sec) Press and release any button on the transmitter to be deleted:
➔
the
LED on the button
DRY
CONT.
flashes quickly.
04.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
3.4.3 - Deleting all transmitters
01.
Press and release the button
DRY
CONT.
: the LED above the button starts blinking slow-
ly, waiting to receive a transmitter.
02.
Hold down the key
RADIO
TEST
and release it when the led
DRY
CONT.
starts flashing quickly.
Led
RADIO
TEST
remains steady on.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
3.4.4 - Memorising a single transmitter button (Mode 2)
01.
Press and release the button
DRY
CONT.
: the LED above the button starts blinking slow-
ly, waiting to receive a transmitter.
02.
On the transmitter
(within 5 sec) press and release the button you want to
store:
On TTPRO BD
➔
LED on the button
DRY
CONT.
flashes quickly.
03.
Press and release the button
F1
F2
F3
and wait until the LED corresponding to the
desired command lights up (see the instruction manual of the motor connected
to TTPRO BD).
04.
Press and release the button
(or the button
) and wait until the LED
corresponding to the desired level lights up.
05.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
3.4.5 - Deleting a transmitter memorised in Mode 2
01.
Press and release the button
DRY
CONT.
: the LED above the button starts blinking slowly,
waiting to receive a transmitter.
02.
Press and release the button
RADIO
TEST
: the LED above the button starts blinking slowly,
waiting to receive a transmitter.
03.
On the transmitter
(within 5 sec) press and release the button on the transmit-
ter to be deleted:
On TTPRO BD
➔
LED on the button
DRY
CONT.
flashes quickly.
04.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
If the transmitter is memorised in...
- Mode 2 = the procedure deletes only the button pressed.
- Mode 1 = the procedure deletes the transmitter, regardless of which button you press.
3.5 - Basic programming
3.5.1 - PROGRAMMING THE DIRECTION OF MOVEMENT
On motors with mechanical limit switch you can change the direction of movement as
follows.
01.
If the direction is not programmed, the buttons
and
will not control the
movements of the motor; moreover, the LEDs above the buttons
DRY
CONT.
and
DRY
CONT.
flash at regular and much shorter intervals.
