English –
6
EN
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
When finished, the LED on the button
AUTO
turns on with a steady light.
Note:
changing position
“1”
erases position
“I”
.
• Programming position “I”
01.
Use the
or
button to bring the roller shutter/awning to the intermediate
position “I” desired.
02.
Press
AUTO
. The key’s led with flash, the
OK
led will flash
GREEN
and the level led
will indicate the number of configurable intermediate positions:
- steady red is the position being configured
- dim steady red indicates a previously configured position
- dim flashing red indicates a position which has not yet been set and which is
available for configuration.
Press
to recall the selected intermediate position if it has already been set.
This facilitates visual verification of the level set at the intermediate position in
question.
Press
or
to move the motor “hold-to-run” mode to finely adjust the previ-
ously configured positions.
03.
➔
Press
OK
to confirm the position. The
OK led is steady green
.
04.
When finished, the LED on the button
AUTO
turns on with a steady light.
05.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
06.
When finished, the LED on the button
AUTO
turns on with a steady light.
Note:
you cannot store position
“I”
if the
“0”
and
“1”
positions have not been stored
previously.
•
If the motor is configured for TWO-WAY communications, and only for
previously configured positions, pressing
DRY
CONT.
followed immediately by
OK
enables
the motor (for around 10 seconds) to pair a key on any remote control to the position
selected in the TTPRO BD.
3.5.2.B - Automatic programming of positions “0” and “1”
In some motors for roller shutters, with electronic limit switches, there is a procedure that
automatically detects positions “0” and “1”. If this feature is available, after TTPRO BD
switches on the LED on the button
AUTO
flashes.
To perform this procedure there must be present on the application the caps on ascent
and/or burglar springs on descent. For more details refer to the motor instructions.
01.
Press the button
AUTO
.
02.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
03.
The motor emits 2 beeps (= start of the procedure).
02.
Press the button with the desired direction:
DRY
CONT.
or
DRY
CONT.
.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
When the operation terminates, the LED on the button corresponding to the cho-
sen direction will be turned on.
Note:
at the end of this programming verify if the transmitter
Ascent
button commands
opening of the roller shutter (or the ascent of the awning), and the
Descent
button com-
mands the closing of the roller shutter (or the descent of the awning). If the direction is
not the desired one, repeat this procedure to programme the other direction.
3.5.2 - PROGRAMMING OF POSITIONS
Motors with electronic limit switches have functions to programme the positions:
“0”
(rolling shutter or awning all rolled up),
“1”
(rolling shutter or awning all unrolled) and
“I”
(rolling shutter or awning in an intermediate position). If a position is already stored, the
corresponding LED will be lit, otherwise a short flash indicates that the position has not
been programmed.
In the menu used to program the positions
“0”
,
“1”
and
“I”
, you can move the motor in
“hold-to-run” mode, thus enabling fine adjustment of the set position. This adjustment is
limited by the limit positions (upper limit for the upper limit switch and lower limit for the
lower limit switch). If you need to move beyond these positions, you must cancel the limit
positions and memorise them anew.
3.5.2.A - Manual programming of positions “0”, “1” and “I”
The positions must be stored in the following order:
“0”
,
“1”
and
“I”
.
The memorisation procedure may vary depending on the type of motor used. Therefore,
refer to the technical specifications which are also available on www.niceforyou.com
site, with details and specific examples for each type of motor.
• Programming position “0”
01.
Use the
or
button to bring the roller shutter/awning to the “0” position
desired.
02.
Press the button
AUTO
: the LED on the button flashes.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
When finished, the LED on the button
AUTO
turns on with a steady light.
Notes
• The direction of movement associated with the button may be not correct until
position
“1”
is stored. • In some types of motors, changing position
“0”
could erase
positions
“0”
and
“I”
.
• Programming position “1”
01.
Use the
or
button to bring the roller shutter/awning to the “1” position
desired.
02.
Press the button
AUTO
: the LED on the button flashes.
