Nice TTPRO BD, Инструкции и предупреждения по установке и использованию

Страница: 8 / 80

7 – English
EN
3.6 - Settings/Adjustments
3.6.1 - SETTING THE TYPE OF “DRY-CONTACT”
01.
Press the button
DRY
CONT.
: the current setting appears on the level LEDs.
02.
Use the or button to turn on the LED that corresponds to the desired
setting.
03.
➔
The green OK LED flashes: (within 3 sec) press the OK button to confirm.
3.6.2 - SETTING THE TIME OF DURATION THE MANEUVER
Warning! - You can set the duration of the maneuver only if limit switches “0” and “1”
have already been set.
01.
Press the button
RDC
: the current setting will appear on the level LEDs.
If the operating time is not programmed, the LED flashes to indicate the closest
approximation, obtained from the motor speed setting.
02.
Use the or button to turn on the LED that corresponds to the desired
setting.
03.
➔
The green OK LED flashes: (within 3 sec) press the OK button to confirm.
Note:
the number of
available levels depends
on: the type of motor
connected, its maximum
and minimum speed
values and the positions
“0” and “1” stored.
Examples of levels available for ERA INN
Level LEDs Maneuver time [sec]
1
5
2 7
3 10
4
15
5 20
6 25
7 30
8 35
9 (A1) 40
10 (A2) 50
11 (A3)
60
12 (A4) 70
13 (A5) 80
14 (A6)
90
15 (A7) 100
16 (A8) 110
04.
The roller shutter must move up: if it goes down, immediately press the button
or to reverse the direction of movement.
05.
At this point the procedure continues automatically: initially, TTPRO BD finds the
“0” position, by the caps, on opening; it then finds position “1” , by the anti-
intrusion springs, on closing.
06.
The motor emits 3 beeps (= end of the procedure) and the roller shutter closes
fully.
07.
Lastly, press the
ON/OFF
button to display the new settings.
3.5.3 - DELETING PRE-PROGRAMMED POSITIONS
• Deleting Position “0”
01.
Press the button
AUTO
: the LED on the button flashes.
02.
Press the button
RADIO
TEST
: the LED on the button flashes.
03.
➔
The green OK LED flashes: (within 3 sec) press the OK button to confirm.
04.
Once this operation terminates, the LED on the button
AUTO
flashes.
• Deleting Position “1”
01.
Press the button
AUTO
: the LED on the button flashes.
02.
Press the button
RADIO
TEST
: the LED on the button flashes.
03.
➔
The green OK LED flashes: (within 3 sec) press the OK button to confirm.
04. Once this operation terminates, the LED on the button
AUTO
flashes.
• Deleting position “I”
01.
Press the button
AUTO
: the LED on the button flashes.
02.
Press the button
RADIO
TEST
: the LED on the button flashes.
03.
➔
The green OK LED flashes: (within 3 sec) press the OK button to confirm.
04.
Once this operation terminates, the LED on the button
AUTO
flashes.
Note: the number of
levels available and the
types of behaviour of
each dry-contact de-
pend on the connected
motor (refer to the motor
manual).
Level LEDs Type of dry contact
1 DRY_1
2 DRY_2
3 DRY_3
4 DRY_4
5 DRY_5
6 DRY_6
7 DRY_7
8 DRY_8