NexComm Systems NEXPEED NBG440 Скачать руководство пользователя

Страница: 44 / 125

NEXPEED NBG440 User’s Manual

NexComm Systems, Inc. 43 PAGE

Configuration example:

In the following example, two routers, NBG440 #1 and NBG440 #2, connect back-to-back over

two pairs SHDSL lines with mx0 interface. Two routers are configured as a bridge and set up the

ethdlc

encapsulation.

In this example, Let’s assume that s0 and s1 are enabled as the

bridging-only

mode. Failure to do

this may cause some or all of the following steps to fail.

Step1:

Disable interfaces of s0, s1.

(conf)# interface s0 bridge disable

(conf)# interface s1 bridge disable

(conf)# show interface

Interface: s0, disabled

Interface: s1, disabled

Interface: lan, status <UP>, mtu 1500

ip address unnumbered

Bridging-only mode

ether 00:d0:84:01:08:b2, speed 10 Mbps half-duplex

(conf)#

Step2:

Using the “device” command, set the data rates at which you want each of the ports.

> Set NBG440 #1 as COE. For best performance, configure the fixed rate mode and the

same bit rate.

(conf)# device s0 gshdsl co 2320

(conf)# device s1 gshdsl co 2320

> Set NBG440 #2 as CPE.

(conf)# device s0 gshdsl rt

(conf)# device s1 gshdsl rt

NBG440 #1

(CO)

mx0

10.0.1.0/24

LAN

NBG440 #2

(RT)

mx0

LAN

Central

Office

Remote

Office

Total Data Rate - 4640kbps

Содержание NEXPEED NBG440






























































































































Результаты поиска

Содержание NEXPEED NBG440

Отзывы:

Похожие инструкции для NEXPEED NBG440

Бренды по названию

Популярные бренды

NexComm Systems NEXPEED NBG440, Руководство пользователя

Результаты поиска

Содержание NEXPEED NBG440

Отзывы:

Похожие инструкции для NEXPEED NBG440

Бренды по названию

Популярные бренды