NexComm Systems NEXPEED NBG440 Скачать руководство пользователя

Страница: 121 / 125

NEXPEED NBG440 User’s Manual

NexComm Systems, Inc. 120 PAGE

NBG440(conf)# ip routing disable lan

⑩

Set the default gateway (for remote management). (If you don’t configure the default gateway,

skip this step.)

NBG440(conf)# ip route add default lan 203.247.170.1

⑪

Save the current configuration to Flash memory.

NBG440(conf)# write config

⑫

Reboot your system.

NBG440(conf)# reboot flash

Configuring NBG440(RT):

①

Use the console port for the configuration. Connect the CONSOLE port to a serial (COM)

port of your computer using the console cable (the enclosed cable in the box). Use a terminal

emulation program with the following parameters:

9600 bps, No parity, 8 data bits, 1 stop bit, NO flow control / VT100 terminal emulation

②

Power on the router and enter the password to log in the router. The default password is a

small letter “password”. If you log in the router, the login prompt

NBG440

> appears.

③

Enter

enable

command and the password to enter configuration mode. The default password is

a small letter “password”. The prompt changes to the configuration mode prompt

(conf)#

Configuration changes can be made only in configuration mode.

NBG440> enable

password:

NBG440(conf)#

④

Restoring the factory default settings and then log in the router again.

NBG440(conf)# write config –default

WARNING !!! this will overwrite the current setting:

Confirm ? (y/n)

=> enter y

NBG440(conf)# reboot flash

⑤

Disable the s0 interfaces. Remove

Bridging

mode from the s0 interface.

NBG440(conf)# interface s0 bridge disable

Содержание NEXPEED NBG440






























































































































Результаты поиска

Содержание NEXPEED NBG440

Отзывы:

Похожие инструкции для NEXPEED NBG440

Бренды по названию

Популярные бренды

NexComm Systems NEXPEED NBG440, Руководство пользователя

Результаты поиска

Содержание NEXPEED NBG440

Отзывы:

Похожие инструкции для NEXPEED NBG440

Бренды по названию

Популярные бренды