New Cosmos Electric PS-7 Скачать руководство пользователя страница 18

Страница: 18 / 50

-15-

7. Operation

7-1. Operation Procedure

Operation Flow

The corresponding numbered steps are given for items 1

–12 on the following pages.

Amber TROUBLE LED
flashes.

Change the set values.

6. Incorrect sensor unit is

inserted.

Need to change

No need to change

12. Initial startup is completed.

11. Perform zero adjustment.

11. Is this for

toxic/combustible gas

detection?

8. Check the set

values.

Yes

6. Self-test

１

Amber TROUBLE LED is off.

Check the tubing for

looseness.

9.10. Check the

sampling gas for flow
rate and airtightness.

Not normal

Normal

11. Is this for low

oxygen detection?

11. Perform 21vol% adjustment.

Yes

2. Turn on the base unit

Base unit startup is

completed.

Initial startup

3. Check the analog

output for base unit

１

Low oxygen detection



Check the power

source.



Check the wiring to the

terminal blocks.

Yes

Install the sensor unit.

Install the main unit.

5. Turn on the main unit.

4. Is the sensor unit

installed?

Do you detect toxic

or combustible gas?

3. Adjust the analog

output for base unit

Yes

Is the main unit off?

Yes

Turn off the main unit.

1. Is power voltage
24 VDC±10%?

Содержание PS-7



















































Результаты поиска

Содержание PS-7

Отзывы:

Похожие инструкции для PS-7

Бренды по названию

Популярные бренды

New Cosmos Electric PS-7, Инструкция по эксплуатации

Результаты поиска

Содержание PS-7

Отзывы:

Похожие инструкции для PS-7

Бренды по названию

Популярные бренды