New Cosmos Electric PS-7 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 50

background image

-12-

6. To install the main unit, pull forward and hold both the latches of the base unit. Connect the main

unit by sliding it onto the rails of the base unit.

7. Push the latches back into place such that the white lines are visible, indicating that the latches

have been locked.

Rail

Fully push latch (lock position).

White line

Latch

WARNING



Ensure that the latches are in the fully locked position (white lines visible). Normal

detection is not possible if the latches are not fully locked.



The protective film is attached to protect the connectors and internal tubing

of the base unit against possible damage while installing the base unit. Once
the main unit has been installed onto the base unit, it is no longer necessary.
Dispose of the used film in accordance with your company

’s rule and

procedure.



When installing multiple PS-7 units side by side, keep sufficient space

(recommended: 30 mm or more) between each pair of the units for main unit
installation/removal.

NOTE

(2) Align with the rail and slide
on.

(1) Pull forward and hold the latches at both sides (unlock position)

«
...
13
14
15
16
17
...
»

Содержание PS-7



















































Отзывы:

Нет отзывов

Похожие инструкции для PS-7

Бренд: Adicos Страницы: 16

WHIXTR130 - XTR-130 Laser/Radar Detector

Бренд: Whistler Страницы: 9

Total Band Protection XTR-475

Бренд: Whistler Страницы: 9

Бренд: Whistler Страницы: 19

Бренд: AJAX Страницы: 48

Бренд: GDS Страницы: 28

Бренд: Coyote Страницы: 52

MULTI-FLEX ACE APEX

Бренд: Garrett Страницы: 26

Бренд: Garrett Страницы: 26

Sea Hunter Mark II None

Бренд: Garrett Страницы: 44

Бренд: GEV Страницы: 21

Бренд: DEGA Страницы: 13

AERASGARD AC02-SD-TYR2

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Tecno Control Страницы: 2

Бренд: Tecno Control Страницы: 2

Бренд: Tecno Control Страницы: 4

Бренд: Tecno Control Страницы: 4

Бренд: Tecno Control Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды