New Cosmos Electric PS-7 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 50

background image

-29-

7-5. Maintenance Mode

Setting

The MNT switch has three modes

— maintenance mode 1 (MNT1), maintenance mode 2 (MNT2), and

normal operation mode (gas-monitoring mode).
Set the MNT switch to MNT1 or MNT2 on

the base unit’s front, accordingly ―MNT1‖ or ―MNT2‖ will be shown

on the LCD. To return to the normal operation mode, set the MNT switch to the center position.

Operation

During MNT1, gas alarm contacts and trouble alarm open collector are disabled.
During MNT2, gas alarm contacts and trouble alarm open collector are disabled, and the analog output is
fixed at 4.0 mA (or 17.4 mA for oxygen).
In either maintenance mode, the amber TROUBLE LED flashes, and the detected gas concentration is shown
on the LCD.

Gas alarm

contact

Trouble

alarm open

collector

Analog output

Amber

TROUBLE

LED

On display

MNT1
(host maintenance mode)

Disabled

(fixed at

OFF)

Disabled

(fixed at ON)

Value

corresponding to
the detected gas

concentration.

Flashes

Detected gas

concentration

value

MNT2

Disabled

(fixed at

OFF)

Disabled

*1

(fixed at ON)

Fixed at 4.0 mA or

17.4 mA

Flashes

Detected gas

concentration

value

WARNING

During normal operation (gas-monitoring mode), ensure the MNT switch is set to the center

position. Gas alarm contacts and trouble alarm open collector do not activate during MNT1/MNT2.
When the MNT switch is set to MNT2, the analog output is fixed at 4.0 mA or 17.4 mA.

MNT switch

MNT1

– normal operation – MNT2

(center)

Lift the cover flap open

CAUTION

*1. Trouble alarm will activate if the main unit

’s power switch is set to the OFF position while in the

MNT1 or MNT2 mode (OFF).

*2. The analog output may change when the main unit

’s power switch is set to the OFF position.

MNT1 or MNT2 modes are enabled with the base unit and without the main unit. The base

unit can produce a 4.0 mA or 17.4 mA analog output while in the MNT2 mode. This function

is useful for loop check at startup, etc.

For COMM-less models, a 4.0 mA or 17.4 mA analog output can be produced only when a

loop checker (LC-7) is attached.

NOTE

«
...
30
31
32
33
34
...
»

Содержание PS-7



















































Отзывы:

Нет отзывов

Похожие инструкции для PS-7

Бренд: Hansen Technologies Страницы: 24

Бренд: Ceia Страницы: 20

Бренд: Jaric Design Страницы: 34

Proline 0330002

Бренд: UFO Страницы: 42

Бренд: Wise Страницы: 18

Бренд: Trotec Страницы: 8

Бренд: Titanium Страницы: 20

Бренд: MD Страницы: 8

Бренд: nalanda Страницы: 12

GMI PS200 Series

Бренд: 3M Страницы: 58

Бренд: Macurco Страницы: 72

Metal Detector GTI 1500

Бренд: Garrett Страницы: 88

Бренд: Duramaxx Страницы: 68

Бренд: AP Страницы: 4

Бренд: Sensidyne Страницы: 4

Бренд: ion science Страницы: 26

Бренд: ion science Страницы: 42

Бренд: Whistler Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды