New Cosmos Electric PS-7 Скачать руководство пользователя страница 46

Страница: 46 / 50

-43-

Power supply

24 VDC



10%

Power
consumption

Sensor unit

CDS-7

COS-7

CHS-7

CDS-7+CDP-7

Typical

2.2 W

2.7 W

2.9 W

5.0 W

Max.

4.2 W

5.0 W

7.8 W

Dimensions

W62 mm × H124 mm × D143 mm (excluding protrusions)

Mass

Approx. 1.0 kg

Mounting method

Wall mounting

*1. Teflon is recommended. For highly adsorptive gas, consult New Cosmos or its authorized

representative for the recommended material.

*2. Specify 1/4 in. and 11/64 in. for outside and inside diameter, respectively, during order placement, if the

standard 6-mm outside and 4-mm inside diameter tubing is not used.

*3 Not provided for COMM-less models.
*4 COMM-less models do not comply with the EMC directive.

* The above specifications are subject to change without notice.
* If your specifications are non-standard, refer to the delivery specifications.

Содержание PS-7



















































Результаты поиска

Содержание PS-7

Отзывы:

Похожие инструкции для PS-7

Бренды по названию

Популярные бренды

New Cosmos Electric PS-7, Инструкция по эксплуатации

Результаты поиска

Содержание PS-7

Отзывы:

Похожие инструкции для PS-7

Бренды по названию

Популярные бренды