New Cosmos Electric PS-7 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 50

background image

-35-

3. Press the top of the rear cover with thumb and pull back the rear cover to separate the rear cover from

the main unit

.

4. Insert a finger between the main unit and the sensor unit so that the sensor unit slightly tilts forward.

Hold the sensor unit by its sides and then pull it out of the main unit.

5. Insert a new sensor unit and place the rear cover back on.

WARNING



If the sensor unit is not completely inserted, an airtight seal will not be created and correct gas

detection will not be possible.

Press here then pull back the rear cover.

Push with palm to insert the sensor unit completely

Insert a finger so that the sensor unit will tilt forward

«
...
36
37
38
39
40
...
»

Содержание PS-7



















































Отзывы:

Нет отзывов

Похожие инструкции для PS-7

Бренд: Medem Страницы: 9

Бренд: Ceia Страницы: 20

12 BAND ESD 9290

Бренд: Cobra Страницы: 13

Бренд: Garett Страницы: 18

Бренд: BEINAT Страницы: 8

Бренд: BEINAT Страницы: 8

Бренд: OKM Страницы: 22

Бренд: OKM Страницы: 46

Бренд: Xtralis VESDA Страницы: 7

Бренд: GDS Страницы: 4

Бренд: MD Страницы: 8

Бренд: ECP Страницы: 4

UNI Sustainable

Бренд: WatchGas Страницы: 10

Бренд: IGD Страницы: 2

JTQ-BF-06TLLoRa

Бренд: SANJIANG Страницы: 5

Бренд: Vallon Страницы: 2

Бренд: Mesutronic Страницы: 84

Бренд: Pilot Communications Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды