background image

Nitric oxide
Colourless  toxic  gas,  relatively  insoluble  in  water.  When  exposed  to  oxygen
(including air), nitric oxide is converted into nitrogen dioxide.

Chemical formula

NO

Molar weight

30

Relative gas density (to air)

1.03

Conversion

1 ppm = 1.23 mg/m

3

Boiling point

-152 °C

Flammability

Nonflammable,  but  accelerates  the
burning of combustible materials.

Odour

Pure NO is odourless, but in the air it
oxidizes  to  NO

2

  which  has  a  pungent

odour

Hazards

Irritates  respiratory  tract  and  eyes,  at
high  concentrations  may  cause  lung
edema and death.

Exposure 

limits

(Directive 91/322/EEC)

TWA

30 mg/m

3

 /25 ppm

IDLH (NIOSH) 123 mg/m

3

 /100 ppm

Conversion of ppm to mg/m

3

 is calculated for 25°C and 1 atm.

Installation guidelines
(See Installation and connections section for general information.)
Nitric  oxide  has  practically  the  same  density  as  air.  As  it  is  easily  oxidized  to  form
nitrogen dioxide, the sensor should be placed as close as possible to the gas source.
Calibration
E2608-NO  detectors  have  been  calibrated  by  Manufacturer  with  standard  gas
mixtures  before  delivery.  Provided  that  the  sensor  is  used  under  moderate
conditions,the  recommended  interval  for  field  recalibration  is  6  months.  Please
contact your dealer for more information.
Maintenance
Do not perform any maintenance operation with the power on.
Clean the device with soft damp cloth. Do not use any abrasive cleaning agents. Do
not immerse the device into water or any cleaning media.
Delivery set
–Detector-transmitter E2608 (wall mount or duct mount version)
– Mounting accessories:

4 cross-shaped mounting lug with screws and 4 screws with plastic dowels for wall
mount version
rubber flange for duct mount version
fixing clamp for remote probe versions

E2608-NO_UM_EN 

         Rev 06.06.2020

Specifications

Sensor type

electrochemical cell

Sampling method

diffusion

Typical detection range

0...250 ppm

Maximum overload

1000 ppm

Resolution / digital unit

1 ppm

Response time T90

< 40 s

Sensor lifetime

> 12 months

Calibration interval

6 months

Signal update

every 1 second

Power supply options

11...30 VDC, 24 VAC

or 90...265 VAC (with mains power unit)

Power consumption

< 2 VA

Load resistance

R

L

 < (Us - 2 V) / 22 mA for 4-20 mA

R

L  

> 250 kOhm for 0-10 V mode

Digital interface

RS485, Modbus RTU protocol

no galvanic isolation

Analog outputs

2 × 4-20 mA / 0-10 V, user settable

Outputs assignment

OUT1 2 gas; OUT2 2 gas

Output scale width

> 10 × resolution

Recommended: 20-100% of the detection range

Relay otputs

2 × SPST, max 5 A, 30 VDC / 250 VAC

Default alarm setpoints

RE1 (LOW): set 10 ppm, release 8 ppm

RE2 (HIGH):set 25 ppm, release 20 ppm

Cable connections

screwless spring loaded terminals

Enclosure

grey ABS, wall mount, protection class IP65

Dimensions

H85 × W82 × D55 mm

CE marking

according to 2014/30/EU and EN61326-1 requirements

Operating conditions

-30...50 °C, 15...90% RH non-condensing, 0,9...1,1 atm

explosion safe indoor areas, non-aggressive atmosphere

NOTE The sensor may exhibit considerable sensitivity to

hydrogen sulfide and nitrogenr dioxide

Warranty
This product is warranted to be free from defects in material and workmanship for a
period  of  one  year  from  the  date  of  original  sale.  During  this  warranty  period
Manufacturer  will,  at  its  option,  either  repair  or  replace  product  that  proves  to  be
defective. This warranty is void if the product has been operated in conditions outside
ranges  specified  by  Manufacturer  or  damaged  by  customer  error  or  negligence  or  if
there has been an unauthorised modification.

         Evikon MCI OÜ

                Teaduspargi 7/9, Tartu

[email protected]

         Tel. +372 733 6310 

  50411 Estonia

www.evikon.eu

PluraSens

®

Nitric Oxide Detector-Transmitter

E2608-NO

User Manual

Содержание PluraSens E2608-NO






Отзывы: