netsys NH-800SP Скачать руководство пользователя страница 6

Страница: 6 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Power Level : Supports High/Low power level settings.

Spanning tree: Supports IEEE-802.1d spanning tree to avoid loop and MAC bridge with redundant link.

MAC address filtering: Supports MAC address filtering security, and MAC learning enable/disable.

TFTP Firmware upgrade: Supports TFTP protocol for remote firmware upgrade using.

SNMP: Supports very strong SNMP function, as RFC-1213 MIBII; RFC-1493 Bridge MIB; RFC-1643 Ether like MIB;

RFC-1757 RNOM MIB, and support 1,2,3,9 RMON groups.

Configuration setting value backup and restore: Supports setting value backup and restore through TFT function.

Default value setting: Supports recovery manufacturing setting value function.

Remote reboot: Supports remote reboot machine through HTTP and Telnet.

Telnet and console setup time limit: If on Login setup manual without keying in any words within 10 seconds time

period, it will be auto logged out.

Preventing Hacker: To avoid hacker to enter management system through client side, it will filter system IP from

client side for preventing hacker attacking.

Web browsers: Supports multiple web browsers: IE/Firefox under WINDOWS O/S, Mozilla & Firefox

under Linux O/S.

Attention:

Be sure to read this manual carefully before using this product. Especially Legal Disclaimer, Statement
of Conditions and Safty Warnings.

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды

netsys NH-800SP, Руководство пользователя

Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды