netsys NH-800SP Скачать руководство пользователя

Страница: 21 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

3.3 General Rules

Before making any connections to the HPNA IP DSLAM, note the following rules:

Ethernet Port (RJ-45)

All network connections to the IP DSLAM’s Ethernet port must be made using Category 5 UTP for 100Mbps and Category

3,4 UTP for 10Mbps.No more than 100 meters (about 328 feet) of cabling may be use between HPNA IP DSLAM or with

HUB or an end node.

HPNA Port (RJ-11)

All Home network connections to the RJ-11Port made

using 18 ~ 26 Gauge

phone wiring.

We do not recommend using 28 Gauge or above phone line.

3.4 Connecting the IP DSLAM

The 8 ports HPNA IP DSLAM has 2 10/100 Mbps N-way ports which support connection to 10Base-T Ethernet or 100Base-TX

Fast Ethernet. Support full or half-duplex operation.The transmission mode is using auto-negotiation. Therefore, the devices

attached to these ports must support auto-negotiation unless they will always operate at half duplex. If transmissions must run at

full duplex, but the attached device does not support auto-negotiation, then you should upgrade this device to a newer version

that supports auto-negotiation.

Use “T” port to connect to devices such as a cable modem, server, bridge or router. You can also cascade to another compatible

MUX or hub by connecting the UP-Link port to an “MDI” port (e.g., port TX on this switch) on the other device.

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды

netsys NH-800SP, Руководство пользователя

Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды