netsys NH-800SP Скачать руководство пользователя страница 13

Страница: 13 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Supports protocol base V-LAN

Supports IEEE-802.1p QOS

Supports IP Multicast / IGMP v1/2 with 512 groups

Supports IEEE 802.1d Spanning trees for MAC bridge with redundant link

Supports port Mirroring(Sniffer)

Supports Broadcast Storm filtering

Supports port security with MAC address filtering

Supports HPNA client port can’t control security for WEB/Telnet management in order to avoid prevent Hacker inrush

Supports Web Base and Telnet for remote control access

Supports POST(Power On Self Testing) LED

Supports SNMP v1 RFC-1493 Bridge MIBs

RFC-1643 Ether like MIBs

RFC-1213 MIB II

◆

Supports RMON groups 1(Statistics), 2(Alarm), 3(Event), 9(History)/ RFC-1757

◆

Supports back up and restore for setting vlaue

◆

Supports Remote reboot

◆

Supports TFTP/XMODEM for firmware upgrade

◆

Supports In-Band/Out-of-Band Management

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

netsys NH-800SP, Руководство пользователя, Страница: 13 / 81

Результаты поиска

Содержание NH-800SP

Отзывы: