netsys NH-800SP Скачать руководство пользователя

Страница: 4 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Safety Warnings

For your safety, be sure to read and follow all warning notices and instructions before using the device.

DO NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other

risks. ONLY qualified service personnel can service the device. Please contact your vendor for further information.

Use ONLY the dedicated power supply for your device. Connect the power cord or power adapter to the right supply voltage

(110V AC in North America or 230V AC in Europe).

DO NOT use the device if the power supply is damaged as it might cause electrocution. If the power supply is damaged,

remove it from the power outlet. DO NOT attempt to repair the power supply. Contact your local vendor to order a new

power supply.

Place connecting cables carefully so that no one will step on them or stumble over them. DO NOT allow anything to rest on

the power cord and do not locate the product where anyone can work on the power cord.

DO NOT install nor use your device during a thunderstorm. There may be a remote risk of electric shock from lightning.

DO NOT expose your device to dampness, dust or corrosive liquids.

DO NOT use this product near water, for example, in a wet basement or near a swimming pool.

Connect ONLY suitable accessories to the device. Make sure to connect the cables to the correct ports.

DO NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.

DO NOT place items on the device.

DO NOT use the device for outdoor applications, and make sure all the connections are indoors. There may be a remote

risk of electric shock from lightning.

Be careful when unplugging the power, because the transformer may be very hot.

Keep the device and all its parts and accessories out of children’s reach.

Clean the device using a soft and dry cloth rather than liquid or atomizers. Power off the equipment before cleansing it.

This product is recyclable. Dispose of it properly.

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды

netsys NH-800SP, Руководство пользователя

Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды