netsys NH-800SP Скачать руководство пользователя

Страница: 2 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Copyright

Trademarks

NETSYS is a trademark of National Enhance Technology Corp.

Other brand and product names are registered trademarks or trademarks of their respective holders.

Legal Disclaimer

The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect

to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the

device, National Enhance Technology Corp. hereby disclaims any and all warranties and liabilities of any kind, including without

limitation warranties of non-infringement of intellectual property rights of any third party.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, NETSYS reserves the right to make changes to

the products described in this document without notice. NETSYS does not assume any liability that may occur due to the use or

application of the product(s) or circuit layout(s) described herein.

Maximum signal rate derived form IEEE Standard specifications. Actual data throughput will vary. Network conditions and

environmental factors, including volume of network traffic, building materials and construction, and network overhead lower actual

data throughput rate. Netsys does not warrant that the hardware will work properly in all environments and applications, and makes

no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness

for a particular purpose. Make sure you follow in line with the environmental conditions to use this product.

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды

netsys NH-800SP, Руководство пользователя

Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды