netsys NH-800SP Скачать руководство пользователя страница 18

Страница: 18 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

2.3 LED Indications

The following describes the function of each LED indicator. (

Table 2-1

)

Table 2-1 LED Indicators Description and Operation

LEDs

Color Status

Descriptions

PWR.

(Power LED)

Green Steady

This LED light is located at the left side on the front panel. It will light up (ON) to

show that the product is receiving power. Conversely, no light (OFF) means the

product is not receiving power.

POST

Green

Steady

POST(Power On Self Test) POST Led will light to show system is booting now.

When system is ready the led will light off.

Steady

LINK/ACT

(Link LEDs)

Green

Blinking

Each RJ45 station port on the Ethernet is assigned an LED light for monitoring port

“Good Linkage”. Each LED is normally OFF after the power on operation, but will

light up steadily to show good linkage. And Flashing to show data transmission.

Speed

(Speed 100 LEDs)

Yellow Steady

Indicates that communications have been set 100 Mbps. Each port on the hub is

assigned an LED light for 100 Base-TX connecting.

Yellow Steady

Indicates that communications have been set to full-duplex operation for the

indicated port

(Full-Duplex LEDs)

Yellow Steady

The indicator lights up working in Full Duplex

And light down working in Half Duplex

LINK

Green Steady

RJ11 LED is lit up to show “Link”. The indicator both CO and CPE side

connecting OK, and light down which Meaning is no connection.

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

netsys NH-800SP, Руководство пользователя, Страница: 18 / 81

Результаты поиска

Содержание NH-800SP

Отзывы: