netsys NH-800SP Скачать руководство пользователя | Manualshive

Страница: 57 / 81

background image

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

56

4.2.2.4.9. SNMP

Any Network Management running the simple Network Management Protocol (SNMP) can management the switch, Provided the

Management Information Base (MIB) is installed correctly on the management station. The SNMP is a Protocol that governs the

transfer of information between management and agent. The HPNA IP DSLAM supports SNMP V1.

1. Use this page to define management stations as trap managers and to enter SNMP community strings. User can also

define a name, location, and contact person for the switch. Fill in the system options data, and then click Apply to update

the changes on this page

Name: Enter a name to be used for the switch.

Location: Enter the location of the switch.

Contact: Enter the name of a person or organization.

2. Community strings serve as passwords and can be entered as one of the following:

«
...
55
56
57
58
59
...
»

Содержание NH-800SP


















































































Отзывы:

Нет отзывов

Похожие инструкции для NH-800SP

Бренд: GW Instek Страницы: 14

Бренд: Alcatel-Lucent Страницы: 386

Бренд: Giga-tronics Страницы: 21

Бренд: Mastech Страницы: 12

OPCOM3100 series

Бренд: Raisecom Страницы: 43

Бренд: Pro's Kit Страницы: 2

Бренд: Maxwell Digital Multimeters Страницы: 19

Бренд: YATO Страницы: 44

Бренд: YATO Страницы: 52

Бренд: YOKOGAWA Страницы: 40

Бренд: Dawson Tools Страницы: 8

Бренд: Dawson Tools Страницы: 12

Бренд: Harris Страницы: 178

Бренд: Omega Страницы: 14

Бренд: Honeywell Страницы: 6

Бренд: Meterman Страницы: 24

Бренд: Wetekom Страницы: 51

Бренд: Tempo Fitness Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды