netsys NH-800SP Скачать руководство пользователя страница 69

Страница: 69 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Serial Console Interface Connector Pin Assignments

The serial console interface connector is a 9-pin, RS-232 D-type, DTE connector. A null modem cable is required to connect a

workstation running the Linux or Windows operating system.

Table A-2

lists the pin assignments for the serial console interface

connector.

Table A-2 RS-232 Connector Pin Assignments

Description

Pin I/O

Signal Name

Not used

Receive data; input

RXD

Transmit data; output

Out

TXD

Data terminal ready; output

Out

DTR

Interface signal ground

GND

Data set ready; input

DSR

Not used

The CDEs have one standard serial port connector located on the

back of the device.

Figure A-4

shows the pin number assignments for

the 9-pin, male D-shell serial port connector on the back of the

device. These pin number assignments conform to the industry

standard for RS-232 communications.

Figure A-4

Figure A-5 Pin Assignments and Wiring for an RS-232 Cable

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

netsys NH-800SP, Руководство пользователя, Страница: 69 / 81

Результаты поиска

Содержание NH-800SP

Отзывы: