netsys NH-800SP Скачать руководство пользователя

Страница: 41 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Protocol Enable Setting:

Enable Spanning Tree Protocol : Default recommend to enable STP.

Enable Internet Group Multicast Protocol: enable IGMP protocol.

VLAN Protocol: 802.1Q(Port_Based) without GVRP VLAN mode.

GVRP (GARP [Generic Attribute Registration Protocol] VLAN Registration Protocol)

GVRP allows automatic VLAN configuration between the switch and nodes. If the switch is connected to a device with GVRP

enabled, you can send a GVRP request using the VID of a VLAN defined on the switch, the switch will automatically add that device

to the existing VLAN.

4.2.2.4.3. Console Port Information

1. Console is a standard UART interface to communicate with Serial Port.

User can launch “HyperTerminal” program to link the switch. Connect To->Configure

Bits per seconds:

9600

Data bits:

Parity:

none

STOP BITS:

Flow control:

none

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды

netsys NH-800SP, Руководство пользователя

Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды