netsys NH-800SP Скачать руководство пользователя

Страница: 80 / 81

NH-800SP 8 PORTS Managed HPNA IP DSLAM USER’S MANUAL Ver_B2

Warranty

The original owner that the product delivered in this package will be free from defects in material and workmanship for one

year parts after purchase.

There will be a minimal charge to replace consumable components, such as fuses, power transformers, and mechanical

cooling devices. The warranty will not apply to any products which have been subjected to any misuse, neglect or

accidental damage, or which contain defects which are in any way attributable to improper installation or to alteration or

repairs made or performed by any person not under control of the original owner.

The above warranty is in lieu of any other warranty, whether express, implied, or statutory, including but not limited to any

warranty of merchantability, fitness for a particular purpose, or any warranty arising out of any proposal, specification, or

sample. We shall not be liable for incidental or consequential damages. We neither assume nor authorize any person to

assume for any other liability.

Содержание NH-800SP


















































































Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды

netsys NH-800SP, Руководство пользователя

Результаты поиска

Содержание NH-800SP

Отзывы:

Похожие инструкции для NH-800SP

Бренды по названию

Популярные бренды