NetApp HCI Скачать руководство пользователя страница 237

Страница: 237 / 363

Check description

Node/cluster

Action needed to
resolve

Knowledgebase article
with procedure

Is DRS enabled and fully
automated?

Cluster

Turn on DRS and make
sure it is fully automated.

See this KB

. NOTE: If you

have standard licensing,
put the ESXi host into
maintenance mode and
ignore this health check
failure warning.

Is DPM disabled in
vSphere?

Cluster

Turn off Distributed Power
Management.

See this KB

Is HA admission control
disabled in vSphere?

Cluster

Turn off HA admission
control.

See this KB

Is FT enabled for a VM on
a host in the cluster?

Node

Suspend Fault Tolerance
on any affected virtual
machines.

See this KB

Are there critical alarms in
vCenter for the cluster?

Cluster

Launch vSphere and
resolve and/or
acknowledge any alerts
before proceeding.

No KB needed to resolve
issue.

Are there generic/global
informational alerts in
vCenter?

Cluster

Launch vSphere and
resolve and/or
acknowledge any alerts
before proceeding.

No KB needed to resolve
issue.

Are management services
up to date?

HCI system

You must update
management services
before you perform an
upgrade or run pre-
upgrade health checks.

No KB needed to resolve
issue. See

this article

for

more information.

Are there errors on the
current ESXi node in
vSphere?

Node

Launch vSphere and
resolve and/or
acknowledge any alerts
before proceeding.

No KB needed to resolve
issue.

Is virtual media mounted
to a VM on a host in the
cluster?

Node

Unmount all virtual media
disks (CD/DVD/floppy)
from the VMs.

No KB needed to resolve
issue.

Is BMC version the
minimum required version
that has RedFish support?

Node

Manually update your
BMC firmware.

No KB needed to resolve
issue.

Is ESXi host up and
running?

Node

Start your ESXi host.

No KB needed to resolve
issue.

Do any virtual machines
reside on local ESXi
storage?

Node/VM

Remove or migrate local
storage attached to virtual
machines.

No KB needed to resolve
issue.

Содержание HCI












































































































































































































































































































































































Результаты поиска

Содержание HCI

Отзывы:

Бренды по названию

Популярные бренды

NetApp HCI, Руководство пользователя

Результаты поиска

Содержание HCI

Отзывы:

Бренды по названию

Популярные бренды