NEC NEAX 2400 IMX Скачать руководство пользователя страница 191

Страница: 191 / 213

CHAPTER 8

ND-70185 (E)

Page 176
Revision 3.0

EX- FCCS
EX-FCCS Features

3. The node that requires the data programming or data change for Number Portability depends on the

pattern. See

Figure 8-5

and

Table 8-2

that explain the eight patterns.

Figure 8-5 Patterns of Number Portability

Note 1:

Destination node

Note 2:

Node to be connected to the FUG where the new number is added

Note 3:

Node where Telephone Number is located before the Number Portability activation

4. Telephone Numbers used in the other FUG and the connected NEAX2000 IVS

system are managed

in the new table in NDM (the table differs from the existing table for Telephone Numbers used in self
FUG).

(a) Telephone Number data in a NEAX2000 IVS

is managed in the NDM of NCNs within all

FUGs and the NEAX2000 IVS

(b) Telephone Number data in a NEAX2400 IMX is managed in the NDM of NCN within all

FUGs.

Table 8-2 Patterns of Number Portability

NO.

PATTERN

(Telephone Number is moved from A to B)

NODE REQUIRED DATA CHANGE

Moving a number within the same FUG

NCN in Center FUG

Moving a number in an FUG to another FUG

NCN in Center FUG

Moving a number in a FUG to a NEAX2000 IVS

NCN in Center FUG + NEAX2000 IVS

Note 1

Adding a new number to an FUG

NCN in Center FUG + NEAX2000 IVS

Note 2

Moving a number in a NEAX2000 IVS

to an FUG

NCN in Center FUG + NEAX2000 IVS

Note 3

Moving a number from a NEAX2000 IVS

to another

NEAX2000 IVS

NCN in Center FUG + a NEAX2000 IVS

Note 3

+ another NEAX2000 IVS

Note 1

Moving a number within the same NEAX2000 IVS

NEAX2000 IVS

Note 1

Note 3

Adding a new number in an NEAX2000 IVS

NCN in Center FUG + NEAX2000 IVS

Note 1

LEGEND

: EX-FCCS

: Fusion Group (FUG)

: FCCS

FUG(A)

IVS

FPC1

NCN(A)

FPC2

FPC4

FPC3

FUG(B)

FPC1

NCN(B)

FPC2

FPC3

FPC4

IVS

: Enhanced CCIS

Get other manuals https://www.bkmanuals.com

Содержание NEAX 2400 IMX






















































































































































































































Результаты поиска

Содержание NEAX 2400 IMX

Отзывы:

Похожие инструкции для NEAX 2400 IMX

Бренды по названию

Популярные бренды

NEC NEAX 2400 IMX, Руководство пользователя

Результаты поиска

Содержание NEAX 2400 IMX

Отзывы:

Похожие инструкции для NEAX 2400 IMX

Бренды по названию

Популярные бренды