NEC NEAX 2400 IMX Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 213

background image

CHAPTER 7

ND-70185 (E)

Page 152
Revision 3.0

TROUBLESHOOTING
3-E PM Lockup Failure (Temporary)

4.1 Repair Procedure

STEP 1:

Make sure that station-to-station connections can be established in the PIM containing the indicated
FCH (PA-FCHA) card.

If the station-to-station connections cannot be established, the PIM is faulty. Repair the PIM. Other-
wise, move to STEP 2.

STEP 2:

Initialize the FCH card using the MB key. See

Figure 7-3

“How to Initialize FCH (PA-FCHA) Card.”

When the LED lights green and no system message related to this failure displays again, monitor the
system for a while. Otherwise, move to STEP 3.

STEP 3:

Replace the FCH card. Refer to

Figure 7-4

“How to Replace FCH (PA-FCHA) Card.”

5. 3-E PM Lockup Failure (Temporary)

The CPU sends diagnosis data at periodic intervals to the Port Microprocessor (PM) on the FCH (PA-FCHA)
cards in order to monitor the PM. If the CPU cannot receive the return data within a predetermined time period,
the system displays this data. When the failure is detected more than 15 times per hour, the failure is judged as
permanent. Otherwise, 3-E “PM Lockup Failure (Temporary)” is displayed.

Figure 7-7 3-E PM Lockup Failure (Temporary)

Note:

B-monitor Restart: Ports whose link have already been established remain connected, while ports process-
ing a call-origination may be released.

Initial Restart: All ports on the circuit card are force released to be placed in idle state.

5.1 Repair Procedure

STEP 1:

If this system message has been displayed only once or twice, monitor the failure for a while. Other-
wise, move to STEP 2.

STEP 2:

Initialize the FCH (PA-FCHA) card using the MB key. See

Figure 7-3

“How to Initialize FCH Card.”

If this message is not displayed any more, monitor the FCH card for a while. Otherwise, move to
STEP 3.

STEP 3:

Replace the FCH card, referring to

Figure 7-4

“How to Replace FCH (PA-FCHA) Card.”

1. xx0x 0000 0000 0000 2. 0000 0000 0000 0000.........

FCH Mounting Location

MG: Module Group

U: Unit (0-3)

G: Group (00-23)

MG

U

G

FCH Mounting Location

PM Restart Type

PM Restart Type

0/1 = B-monitor / Initial Restart

Note

Get other manuals https://www.bkmanuals.com

«
...
165
166
167
168
169
...
»

Содержание NEAX 2400 IMX






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NEAX 2400 IMX

QSR-3920 Series

Бренд: QTech Страницы: 120

Бренд: QSC Страницы: 28

Бренд: SAF Страницы: 30

Бренд: Lindy Страницы: 4

Бренд: JETWAY Страницы: 55

Бренд: Tbus Страницы: 25

Бренд: Faderfox Страницы: 10

Бренд: Paradyne Страницы: 10

Бренд: protech Страницы: 95

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренд: Patton electronics Страницы: 9

Бренд: Qlogic Страницы: 8

Бренд: ZALMAN Страницы: 5

RouterBOARD 411R

Бренд: 4gon Страницы: 2

Бренд: Gira Страницы: 6

Бренд: Uniden Страницы: 5

Бренд: Techroutes Страницы: 20

Бренд: Solwise Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды