NEC NEAX 2400 IMX Скачать руководство пользователя страница 107

Страница: 107 / 213

CHAPTER 5

ND-70185 (E)

Page 92
Revision 3.0

DATA PROGRAMMING
Assignment of FCH Related Data

STEP 5:

ARTD/ARTDN

Using ARTD, assign the following CDN data for the dummy route number.

Note 1

CDN 6 (TCL)=1 or 4 (depending on requirement)

CDN 7 (L/T)=1

CDN 13 (AC)=1

The other CDNs may be left default (data 0) for the dummy route.

STEP 6:

AFRSL/AFRSN

Note 2

Using AFRSL, assign the Number Pattern Code (NPC) and the Outgoing Route Selection Pattern
Number (OPR) for the dummy route number.

LGRT=Dummy route number

NPC=8110

OPR=1

STEP 7:

AOPRL/AOPRN

Note 2

Using AOPRL, assign the external route number to OPR assigned in the AFRSL command.

TDPTN=0

OPR=1

RA=0

E=1

LGRT=10

SKIP=4

PNL=0

OVFT=0

PRSC=0

TDPTN=0

OPR=1

RA=1

E=0

LGRT=200

SKIP=8

PNL=128

OVFT=0

PRSC=0

STEP 8:

AADCL/AADCN

Note 2

Using AADCL, assign the additional Digit Code to PNL assigned in the AOPRL command.

PNL=128

DC=12025678901

STEP 9:

ARSCN

Using ARSCN, assign the Route Restriction Class (RSC) that allows RRIs for the external trunk
route. The same route restriction data must be assigned for each node.

Note 1:

The dummy route must be assigned to all nodes (including a node which does not have external routes).

Note 2:

When entering the data in STEP 1, 2, 6, 7 and 8, do not mix the commands for LDM and NDM. Write the
data on the same data memory as shown below:

•

When writing the data on the LDM:

ANPDL

→

ASPAL

→

AFRSL

→

AOPRL

→

AADCL

(STEP 1)

(STEP 2)

(STEP 6)

(STEP 7)

(STEP8)

•

When writing the data on the NDM:

ANPDN

→

ASPAN

→

AFRSN

→

AOPRN

→

AADCN

(STEP 1)

(STEP 2)

(STEP 6)

(STEP 7)

(STEP8)

Get other manuals https://www.bkmanuals.com

Содержание NEAX 2400 IMX






















































































































































































































Результаты поиска

Содержание NEAX 2400 IMX

Отзывы:

Похожие инструкции для NEAX 2400 IMX

Бренды по названию

Популярные бренды

NEC NEAX 2400 IMX, Руководство пользователя

Результаты поиска

Содержание NEAX 2400 IMX

Отзывы:

Похожие инструкции для NEAX 2400 IMX

Бренды по названию

Популярные бренды