NEC NEAX 2400 IMX Скачать руководство пользователя страница 153

Страница: 153 / 213

CHAPTER 6

ND-70185 (E)

Page 138
Revision 3.0

POST INSTALLATION TEST
FCCS Network Connection Test

Figure 6-7 Fusion Link-Test Results

STEP 4:

Return Mode to 8 (standard setting) when the test is complete.

STEP 5:

Initialize the FCH (PA-FCHA) card using the MB switch.

Note:

Be sure to initialize the FCH (PA-FCHA) card, after changing the setting of the Mode Switch.

3. FCCS Network Connection Test

This section explains how to perform the following connection tests within the Fusion network:

•

Station-to-Station Connection Test (via FCCS)

•

ATTCON Connection Test (via FCCS)

•

Line (LC, ELC, DLC card) Connection Test (via FCCS)

•

3-party Conference Trunk Function Test (via FCCS)

3.1 Station-to-Station Connection Test (via FCCS)

Perform the station-to-station connection test, following the procedure listed below.

3.1.1

FCCS Call Origination Test

STEP 1:

Using the MBCT command, make busy all trunks in the route except the trunk to be tested.

STEP 2:

Lift the handset of STN A in Node A.

STEP 3:

Dial a Telephone Number (STN B) which belongs to another node.

Mode

LYR

LOAD

EST3

EST2

EST1

EST0

Remains ON

when available

for Ethernet

Remains ON

when ready to broadcast

data packets Note

Link is

established

Receive

Receive Polarity of

pair-wire is normal

Send

Flash

Front View

Make sure that the LYR LED flashes at 60-INT.

DTI

FCH

MNT

Front View

FCH (PA-FCHA) card

When the result of test

is OK, the LYR LED

flashes.

Note:

When the FCH is a “Root Bridge”, the LOAD LED remains ON.

Check

Get other manuals https://www.bkmanuals.com

Содержание NEAX 2400 IMX






















































































































































































































Результаты поиска

Содержание NEAX 2400 IMX

Отзывы:

Похожие инструкции для NEAX 2400 IMX

Бренды по названию

Популярные бренды

NEC NEAX 2400 IMX, Руководство пользователя

Результаты поиска

Содержание NEAX 2400 IMX

Отзывы:

Похожие инструкции для NEAX 2400 IMX

Бренды по названию

Популярные бренды