NEC NEAX 2400 IMX Скачать руководство пользователя страница 212 | Manualshive

Страница: 212 / 213

background image

ND-70185 (E)

CHAPTER 8

Page 197

Revision 3.0

EX- FCCS

Data Programming

1.

To Log-in to All Nodes in EX-FCCS Network

To upgrade CCIS network to EX-FCCS Network as shown in the figure on the previous page, all the IMX sys-
tems are set as NCNs respectively. To construct a EX-FCCS Network including stand-alone IMX system, the
node must be assigned as a Fusion Network configured by the NCN only, and handled by the NDM data. Assign
the following data at all the NCNs (that is, all the IMX systems of each node) within the EX-FCCS Network.

STEP 1:

AFUGN

Assign EX-FCCS Fusion Group data such as Self FUG Number and connection FUG Number des-
ignating Fusion Point Code of the NCN within FUG. Assign one of the IMX systems as the Center
Fusion Group by clicking the check box in the “CENTER” parameter.

STEP 2:

AEXFN

Assign the CCH Selection Data by designating all the Fusion Point Code (FPC) and the Point Code
(PC) in the connected Fusion Group.

Note:

Confirm the Centralized MAT can log in to each node here. Reexamine the assigned data if log-in can not
be executed. There may be some error in data setting so far.

2.

To Access to EX-FCCS Trunk via EX-FCCS Telephone Number

Assign the following data to activate originating calls via EX-FCCS trunk. EX-FCCS Abbreviated Digit Code
(ADC) must be assigned by using AEADN command at all the IMX nodes in the network. Only at the NCN of
the Center Fusion Group, allocate EX-FCCS Telephone Numbers for all the stations in the network uniquely.

AEADN: Assign the ADC (Abbreviate Digit Code) for connection Fusion Group. Enter the FUG Number as-

signed by AFUGN command, TN, and ADC to be assigned.

AELGN: Telephone Numbers must be assigned for all the station within the network uniquely. Use AELGN

command to allocate EX-FCCS Telephone Number. FUG data must be assigned previously by
AFUGN command to activate this command.
Only readout function can be used by this command in case both the Self FUG Number and the Con-
nection FUG Number are assigned, if the Self FUG is not the Center FUG.

Note 1:

Refer to the service feature manual for NEAX2000 IVS

2

system as to the data programming on NEAX2000

IVS

2

side.

Note 2:

Check whether the trunk originating call via CCIS can be executed by dialing EX-FCCS Telephone Number
here. Reexamine the assigned numbering plan data if the call cannot be connected. There may be some er-
ror in the data setting so far.

<All the nodes consist of IMX system>

<NCN of the Center FUG>

Get other manuals https://www.bkmanuals.com

«
...
210
211
212
213
»

Содержание NEAX 2400 IMX






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NEAX 2400 IMX

Бренд: Lattice Semiconductor Страницы: 15

Бренд: Clavister Страницы: 89

Бренд: Lorex Страницы: 186

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Бренд: NetComm Страницы: 69

Бренд: Freund Страницы: 6

Бренд: MEDIATEK Страницы: 166

Бренд: MICROENER Страницы: 24

PCard-E 021L-D5 Series

Бренд: ORiNG Страницы: 2

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренд: Hamlet Страницы: 11

Бренд: Eagle Technology Страницы: 39

Бренд: Renesas Страницы: 4

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: Z3 Technology Страницы: 22

Бренд: DHD Power Cruiser Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды