NEC NEAX 2400 IMX Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 213

background image

ND-70185 (E)

CHAPTER 5

Page 59

Revision 3.0

DATA PROGRAMMING

Network Data Programming Summary

1.2 Upgrading a CCIS Network

To install the Fusion system to an existing CCIS network, the overall programming procedure is as follows:

1.2.1

System Data

•

Decide an NCN and LN on the network.

•

Assign System Data for each node. Use the ASYDN command for NCN and the ASYDL command
for LN. The system data includes the size of LDM, NDM, Fusion Point Code (FPC), etc.

Note:

The data becomes effective by executing “Non-Load Initial” after setting the FPC.

•

Assign unit data using the AFMU command for each node which exists on the network. Note the
AFMU command is available at NCN only.

•

Assign Logical Route Numbers of all routes (external trunk) on the network using the ALRTN com-
mand. Note that the ALRTN command is available at NCN only.

1.2.2

Numbering Plan Data

•

ANPDN

→

ASPAN (for NCN only): Assign numbering plan data for Telephone Number.

•

When “Operator Call” or “Priority Call (ATT)” is used on the Fusion network, replace the existing
numbering plan data for these features using the ANPDL and ASPAL commands.

Note:

The Numbering Plan data for the LDM and/or NDM cannot use separate Tenant Numbers (TN). Therefore,
be sure to assign the following data on the ASYDL command.

•

ASYDL command, SYS1, INDEX 800
b1 = 1 (ASPAL command tenant data table development on LDM = Common)
b2 = 1 (ANPDL command tenant data table development on LDM = Common)

1.2.3

Station Numbering

•

Assign Telephone Numbers using the following commands:
ALGNN

→

ALGSN: Assign Telephone Number at network level. (NCN only)

1.2.4

Fusion Link Data

•

Assign the Fusion Link data using the following commands:
Fusion with FCH: ACRD

→

ACTK

→

ACAN

→

MBCT

→

AFCH

→

AFPC

→

AFRT

Fusion w/o FCH: ACRD

→

ACTK

→

ACAN

→

MBCT

→

AFPC

Note:

When the Fusion system is incorporated in an existing CCIS network, all nodes must be linked via CCIS on
the network.
If there are any nodes linked via ACIS alone, add the CCIS link before the installation of the Fusion link
(See

Figure 5-2

.) Please refer to CCIS-related manuals for more detailed information.

Get other manuals https://www.bkmanuals.com

«
...
72
73
74
75
76
...
»

Содержание NEAX 2400 IMX






















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NEAX 2400 IMX

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 221

Express Ethernetwork DI-707P

Бренд: D-Link Страницы: 14

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: Quick Eagle Networks Страницы: 4

Бренд: Watchguard Страницы: 39

Бренд: Enginko Страницы: 19

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

Avenue Express Control Panel

Бренд: Ensemble Designs Страницы: 19

Бренд: FS Страницы: 19

Бренд: EnGenius Страницы: 3

Бренд: 4G Systems Страницы: 2

Бренд: TRENDnet Страницы: 10

Бренд: Matrix Switch Corporation Страницы: 60

Network Adapter ADZIFCF

Бренд: Addonics Technologies Страницы: 1

Бренд: Juniper Страницы: 396

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды