NEC mPD780208 Subseries Скачать руководство пользователя страница 209

Страница: 209 / 418

CHAPTER 13 SERIAL INTERFACE CHANNEL 0

209

User’s Manual U11302EJ4V0UM

(1) Serial I/O shift register 0 (SIO0)

This is an 8-bit register used to carry out parallel/serial conversion and serial transmission/reception (shift

operations) in synchronization with the serial clock.

SIO0 is set with an 8-bit memory manipulation instruction.

When bit 7 (CSIE0) of serial operating mode register 0 (CSIM0) is 1, writing data to SIO0 starts serial

operation.

In transmission, data written to SIO0 is output to the serial output (SO0) or serial data bus (SB0/SB1).

In reception, data is read from the serial input (SI0) or SB0/SB1 to SIO0.

The bus configuration in SBI mode and 2-wire serial I/O mode enables the pin to function as both an input

and output pin. Thus, when a device is receiving, write FFH to SIO0 in advance (except when address

reception is carried out by setting bit 5 (WUP) of CSIM0 to 1).

In the SBI mode, the busy state can be cleared by writing data to SIO0. In this case, bit 7 (BSYE) of

the serial bus interface control register (SBIC) is not cleared to 0.

RESET input makes SIO0 undefined.

(2) Slave address register (SVA)

This is an 8-bit register used to set the slave address value for connection of a slave device to the serial

bus. This register is not used in the 3-wire serial I/O mode.

SVA is set with an 8-bit memory manipulation instruction.

The master device outputs a slave address to the connected slave devices for selection of a particular

slave device. These two data (the slave address output from the master device and the SVA value) are

compared by the address comparator. If they match, the slave device has been selected. In that case,

bit 6 (COI) of serial operating mode register 0 (CSIM0) becomes 1.

Address comparison can also be executed on the data of the LSB-masked higher 7 bits by setting bit

4 (SVAM) of the interrupt timing specification register (SINT) to 1.

If no matching is detected in address reception, bit 2 (RELD) of the serial bus interface control register

(SBIC) is cleared to 0. The wakeup function can be used by setting bit 5 (WUP) of CSIM0 to 1. In this

case, the interrupt request signal (INTCSI0) is generated only when the slave address output by the

master matches the value of SVA, and it can be ascertained by this interrupt request that the master is

requesting communication. If bit 5 (SIC) of the interrupt timing specification register (SINT) is set to 1,

the wakeup function cannot be used even if WUP is set to 1 (an interrupt request signal is generated when

bus release is detected). To use the wakeup function, clear SIC to 0.

Further, an error can be detected by using SVA when the device transmits data as a master or slave device

in the SBI or 2-wire serial I/O mode.

RESET input makes SVA undefined.

(3) SO0 latch

This latch holds the SI0/SB0/P25 and SO0/SB1/P26 pin levels. It can be directly controlled by software.

In the SBI mode, this latch is set at the end of the 8th serial clock.

(4) Serial clock counter

This counter counts the serial clocks to be output and input during transmission/reception and checks

whether 8-bit data has been transmitted/received.

(5) Serial clock controller

This circuit controls serial clock supply to serial I/O shift register 0 (SIO0). When the internal system

clock is used, the circuit also controls clock output to the SCK0/P27 pin.

Содержание mPD780208 Subseries



































































































































































































































































































































































































































Результаты поиска

Содержание mPD780208 Subseries

Отзывы:

Похожие инструкции для mPD780208 Subseries

Бренды по названию

Популярные бренды

NEC mPD780208 Subseries, Руководство пользователя

Результаты поиска

Содержание mPD780208 Subseries

Отзывы:

Похожие инструкции для mPD780208 Subseries

Бренды по названию

Популярные бренды