NEC Express 5800/120Lh Скачать руководство пользователя страница 80

Страница: 80 / 314

4-14 Configuring Your Server

Server

Option

Parameter

Description

Your Setting

System
Management

–

System Management submenu is
displayed.

Console
Redirection

–

Console Redirection submenu is
displayed.

Assert NMI on
PERR

Disabled
[Enabled]

Indicates whether PCI PERR is
supported or not.

Assert NMI on
SERR

Disabled
[Enabled]

Indicates whether PCI SERR is
supported or not.

Post Error Pause

Disabled
[Enabled]

Indicates whether POST is aborted once
at the end of POST if an error occurs
during the execution of POST.

AC LINK

Stay Off
[Last State]
Power On

Indicates the AC LINK function. Shows
the state of the power of the server.

[ ]: Factory-set

IMPORTANT:

To power on the server from the UPS (Uninterruptible

Power Supply), select [Server] - [AC Link] - [Power On].

The table below shows the operation when the AC power to the server is turn off once and then on
again, depending on the setting of "AC LINK."

Setting of AC LINK

System status before AC power off

Stay Off

Last State

Power On

Operating

Off

Aborting (DC power being off also)

Off

Forced shutdown

Off

* Press the power switch continuously for four seconds or longer. This forcibly turns off the

power.

Содержание Express 5800/120Lh



























































































































































































































































































































Результаты поиска

Содержание Express 5800/120Lh

Отзывы:

NEC Express 5800/120Lh, Руководство пользователя, Страница: 80 / 314

Результаты поиска

Содержание Express 5800/120Lh

Отзывы: