NEC Express 5800/120Lh Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 314

NEC Express 5800/120Lh Скачать руководство пользователя страница 115

Installing the Operating System with Express Setup 5-23

Exceptional Setup

This section explains how to setup with the exceptional way. You usually do not have to do as
follows. If your system has any Mass storage devices, you have to set as follows depending on your
system. The detailed information is provided by the manual of the Mass storage device.

Installation of Mass storage device not to be supported by ExpressSetup

If you would like to install or re-install the OS when the system has new mass storage device not to
be supported by NEC EXPRESSBUILDER, you have to set as follows.

1.

Read the manual supplied with the mass storage device before setting the server.

2.

If the mass storage device is disk array controller, configure the RAID system before
running the NEC EXPRESSBUILDER.

3.

Boot the system from NEC EXPRESSBUILDER CD-ROM.

4.

(a) When the dialog of Disk array configuration appears, check "Use Existing Array".

(b) Check "Apply OEM-FD for Mass storage device".

5.

Copy the driver for the mass storage device in the ExpressSetup.

Insert the floppy disk attached the mass storage device into the floppy disk drive.

Continue the ExpressSetup, referring to messages displayed on the display.

«
...
113
114
115
116
117
...
»

Содержание Express 5800/120Lh



























































































































































































































































































































Отзывы:

Нет отзывов