NEC Express 5800/120Lh Скачать руководство пользователя страница 204

Страница: 204 / 314

8-30 Troubleshooting

Collect Configuration Information

This section describes on how to collect the information on hardware configuration and inside
specification.

In order to collect information, "Diagnostic Program" is used.

IMPORTANT:

If STOP error, system error, or stall occurred, follow

the procedure below after restarting the system.

Refer to Windows online help.

Point to [Settings] in Start menu, and click [Control Panel].

The [Control Panel] dialog box appears.

Double-click [Management Tool], and double-click [Computer Management].

The [Computer Management] dialog box appears.

Click [System Tool]

→

[System Information].

Click [Save as System Information File] in the [Operation] menu.

Input the file name to save in the [File Name] box.

Click [Save].

Содержание Express 5800/120Lh



























































































































































































































































































































Результаты поиска

Содержание Express 5800/120Lh

Отзывы:

NEC Express 5800/120Lh, Руководство пользователя, Страница: 204 / 314

Результаты поиска

Содержание Express 5800/120Lh

Отзывы: