manualshive.com logo in svg

NEC Express 5800/120Lh, Руководство пользователя, Страница: 270 / 314

Поделиться
Скачать
NEC Express 5800/120Lh Скачать руководство пользователя страница 270

10-6  Internal Cabling Diagrams

Installing a SCSI File Device

With the standard configuration, you need an optional SCSI controller and internal SCSI cable to
install a file device.

IMPORTANT:

 Onboard SCSI channels are controlled for the RAID

hard disk drives when an optional RAID controller (N8103-86F) is
installed.

Set SCSI IDs as shown in the above figure. Set the terminator (Enabled/Disabled) for the last-
connected device in the SCSI chain. Set "Disabled" for all the middle devices. A terminating
connector may be installed depending on the internal SCSI cable. If the SCSI cable ends with a
terminating resistor, set "Disabled" for all the terminating resistors of connected devices. For the
settings, see the manual provided with each device.

A file device needs settings such as a SCSI transfer rate. For the transfer rate, see the manual
provided with the file device. Use the BIOS utility of the SCSI controller to make the settings. For
details, see the manual provided with the SCSI controller.

An onboard Ultra320 SCSI connector can be used to connect with internal SCSI file device.

Terminator

5.25-inch
device bay

3.5-inch
hard disk
bay

Mother board

Floppy disk

drive

SCSI deive ID2

SCSI device ID1

CD-ROM

SCSI device ID0

PCI -X #6

PCIe #5
PCIe #4

PCI-X #3
PCI-X #2

PCI #1

SCSI #A

Fl

oppy di

sk

SCSI cable

Floppy disk drive cable

IDE cable

SC

SI #

B

IDE

ID5
ID4
ID3
ID2
ID1
ID0

Содержание Express 5800/120Lh



























































































































































































































































































































Отзывы:

Нет отзывов