manualshive.com logo in svg

NEC Express 5800/120Lh, Руководство пользователя, Страница: 293 / 314

Поделиться
Скачать
NEC Express 5800/120Lh Скачать руководство пользователя страница 293

Installing Windows Server 2003    D-9

Reinstallation to Multiple Logical drives

This subsection describes the procedure for reinstalling the operation system if the multiple logical
drives exist.

Before Re-installing the Operation System

Be sure to make backup copies before re-installing the operation system just in case.

Re-installing the Operation System

 

1. 

Start the clean installation following the procedure described in this manual.

 

2. 

Specify the partition in which you want to install the operating system when the following
message appears:

The following list shows the existing partitions and
unpartitioned space on this computer.

Use the UP and DOWN ARROW keys to select an item in the list.

*

Cannot modify the drive letter of your system or boot volume. Confirm the proper
drive letter is assigned and then, continue the setup.

 

3. 

Continue the clean installation again following the procedure described earlier in this
chapter.

The drive letter of the re-installed system may differ from the one of the previous system.
If you need to modify the drive letter, modify it according to the "Procedure for
Modifying the Drive Letter".

Содержание Express 5800/120Lh



























































































































































































































































































































Отзывы:

Нет отзывов