manualshive.com logo in svg

NEC Express 5800/120Lh, Руководство пользователя, Страница: 213 / 314

Поделиться
Скачать
NEC Express 5800/120Lh Скачать руководство пользователя страница 213

Chapter 9

Upgrading Your Server

This chapter describes internal optional devices available for the server, procedures for install or
removing such optional devices, and notes on using them.

IMPORTANT:

„

 

You may conduct the installation and removal procedures described
in this section by yourself.    However, NEC is not responsible for
any machine or component defects or bad influences resulting from
the operation of the server subject to the installation or removal.
NEC recommends that you request a maintenance engineer of your
service representative having the expert knowledge on the server to
do the installation and removal procedures.

„

 

Use the options and cables approved by NEC.    You will be charged
by any repair of a malfunction, fault, or defect occurring in a server
in which one or more component not approved by NEC are used.

„

 

Always update the system if the hardware configuration is changed
(See Chapter 5 for details).

Содержание Express 5800/120Lh



























































































































































































































































































































Отзывы:

Нет отзывов