NEC Express 5800/120Lh Скачать руководство пользователя страница 23

Страница: 23 / 314

Notes on Using Your Server 1-9

TRANSFER TO THIRD PARTY

The following must be observed when you transfer (or sell) the server or software provided with the
server to a third party:

Server hardware

Make sure to provide this manual along with the server to a third party.

IMPORTANT:

It is the user's responsibility to completely erase or

modify all the data stored in storage device such as hard disk so that the
data cannot be restored.

Provided software

To transfer or sell any software application that comes with the server to a third party, the following
requirements must be satisfied:

All provided software applications must be transferred and no backup copies must be
retained.

Transfer requirements listed in "Software License Agreement" that comes with each
software application must be satisfied.

Software applications that are not approved for transfer must be uninstalled before
transferring the server.

Содержание Express 5800/120Lh



























































































































































































































































































































Результаты поиска

Содержание Express 5800/120Lh

Отзывы:

NEC Express 5800/120Lh, Руководство пользователя, Страница: 23 / 314

Результаты поиска

Содержание Express 5800/120Lh

Отзывы: