NEC Express 5800/120Lh Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 314

NEC Express 5800/120Lh Скачать руководство пользователя страница 49

General Description 2-23

SLEEP Switch

You can use the POWER switch as the SLEEP switch if the ACPI compliant operating system is
installed in your system.

The SLEEP switch allows you to save almost all power of the server (power-saving mode or sleep
mode).

NOTE:

To use the SLEEP switch, an OS supporting the sleep feature

is required. (Available for Windows 2000.)

Press the SLEEP switch on the front of the server to place the server in the power-saving mode.
(The POWER/SLEEP lamp blinks.) In the power-saving mode, the server retains the memory data
and the status of the previous operations.

To resume the original state, press the POWER switch. (It may take a little time to resume the
original state.)

NOTE:

The operational level in the power-saving mode depends on

the OS in use. (Available for Windows Server 2003 and Windows
2000.)

IMPORTANT:

Do not change system configuration while turning into

the power-saving mode or in the power-saving mode. Otherwise, you
may fail to resume the original state.

POWER/SLEEP lamp

«
...
47
48
49
50
51
...
»

Содержание Express 5800/120Lh



























































































































































































































































































































Отзывы:

Нет отзывов