manualshive.com logo in svg

NEC Express 5800/120Lh, Руководство пользователя, Страница: 184 / 314

Поделиться
Скачать
NEC Express 5800/120Lh Скачать руководство пользователя страница 184

8-10  Troubleshooting

POST Error Messages

When POST detects an error, it displays an error message on the display unit screen.    The
following table lists error codes, error messages, and actions to take.

IMPORTANT:

 Take a note on the messages displayed before

consulting with your sales agent.    Alarm messages are useful
information for maintenance.

Error
code

Error message

Recommended Action

0200

Failure Fixed Disk.

Contact your service representative.

0210

Stuck Key.

Disconnect the keyboard and connect it again.

0213

Keyboard locked - Unlock key switch.

Release the lock of the key switch.    If the
error cannot be corrected in spite of the
release of the lock, contact your service
representative.

0220

Monitor type does not match CMOS - Run
SETUP.

Start the SETUP.    If the error cannot be
corrected in spite of the start of SETUP,
contact your service representative.

0230

System RAM Failed at offset.

0231

Shadow Ram Failed at offset.

0232

Extended RAM Failed at address line.

Contact your service representative.

0250

System battery is dead - Replace and run
SETUP.

Contact your service representative to replace
the battery.    (After restarting the computer,
start the SETUP to provide the setting again.)

0251

System CMOS checksum bad - Default
configuration used.

The default values have just been set.    Start
the SETUP to provide the setting again.    If
the error cannot be corrected, contact your
service representative.

0252

Password checksum bad - Passwords
cleared.

The password has just been cleared.    Start
the SETUP to provide the setting again.

0260

System timer error.

0270

Real time clock error.

0271

Check date and time setting.

Start the SETUP to set the date and time
again.    If the same error occurs successively
in spite of the resetting, contact your service
representative.

02B0

Diskette drive A error.

Start the SETUP to set the "Legacy Floppy A"
in the Main menu again.    If the same error
occurs successively in spite of the resetting,
contact your service representative.

02B2

Incorrect Drive A type - run SETUP.

Start the SETUP to provide the setting again.
If the error cannot be corrected, contact your
service representative.

02D0

System cache error - Cache disabled.

The cache cannot be used.    Contact your
service representative.

Содержание Express 5800/120Lh



























































































































































































































































































































Отзывы:

Нет отзывов