Nautel Exporter Plus Скачать руководство пользователя страница 39

Страница: 39 / 186

Exporter Plus Technical Instruction Manual

Quick setup procedure

Issue 1.0 2020-05-05

Page 6-1

Section 6:

Quick setup procedure

This section provides information on setting up the Exporter Plus with the goal of being on-air

with an

IBOC

signal.

•

Starting the Exporter Plus - see page 6-2

•

Verifying operating mode - see page 6-3

•

Setting time zone offset - see page 6-4

•

Configuring the network - see page 6-5

•

Configuring the exciter - see page 6-7

•

Checking status and alarms - see page 6-8

•

Checking audio input levels - see page 6-9

•

Checking GPS status - see page 6-10

•

Checking LAN status - see page 6-11

•

Setting audio diversity delay - see page 6-12

•

Setting/verifying station information - see page 6-13

Note: Refer to

Section 8, “Operating” on page 8-1

for a complete hierarchy of all user

interface (UI) menu options as well more detailed information on any of the user

interface pages referenced in this section.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 39 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: