Nautel Exporter Plus Скачать руководство пользователя страница 112

Страница: 112 / 186

Exporter Plus Technical Instruction Manual

Operating

Page 8-42

Issue 1.0 2020-05-05

Audio monitor

From the

AUDIO MONITOR

menu (see

Figure 8.90

) you can configure audio being monitored at

the front panel headphone jack and rear panel monitor output. This menu also provides

selection of internally generated audio signals for test purposes. To use a test tone, select it as an

audio source and then connect the monitor output to either the analog or digital audio input.

Figure 8.90: Audio Monitor Menu

Setting audio source for headphone jack

When you select

Audio Source

from the

AUDIO MONITOR

menu (see

Figure 8.91

) you can

select the type of audio source being monitored at the front panel headphone jack and rear

panel monitor output

Figure 8.91: Audio Source Screen

To change the audio source type, press the checkmark (accept) button to enter the editing

screen shown in

Figure 8.92

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 112 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: