Nautel Exporter Plus Скачать руководство пользователя страница 54

Страница: 54 / 186

Exporter Plus Technical Instruction Manual

Remote interfacing

Page 7-2

Issue 1.0 2020-05-05

Table 7.1: Station Interface Connector Digital I/O

Signal

Direction (Level)

Function

Pin

Not Used

Input (Open/Ground)

Diversity Delay
Ramp Up

Input (Open/Ground)

Ramps up diversity delay when ground is applied.

Diversity Delay
Ramp Down

Input (Open/Ground)

Ramps down diversity delay when ground is applied.

Diversity Delay
Increase

Input (Open/Ground)

Increases diversity delay by the amount set in the UI (see
“Setting Delay Increment”) when ground is applied.

Diversity Delay
Decrease

Input (Open/Ground)

Decreases diversity delay by the amount set in the UI (see
“Setting Delay Increment”) when ground is applied.

Audio Bypass On/
Off

Input (Open/Ground)

Bypasses analog audio when ground is applied.

1PPS Out

Output (3.3 V/Ground)

Passes through interface card from Exporter PCI card.

Watchdog Disable

Input (Open/Ground)

Application watchdog is disabled when ground is applied.

Power On/Off

Input (Open/Ground)

Power switches off when ground is applied and on when
changed from ground to open circuit.

Ramp Status

Output (Open/Ground)

Ground potential (0 V) when the target ramp state has been
set to ‘up’. Open circuit when the target ramp state has been
set to ‘down’.

Delay Inc/Dec

Output (Open/Ground)

Ground potential (0 V) when analog audio is ramping up or
down. Open circuit when it is not ramping up or down.

Bypass Status

Output (Open/Ground)

Ground potential (0 V) when analog audio is being bypassed.
Open circuit when it is not being bypassed.

1 PPS In

Input (3.3 V/Ground)

Passes through interface card to Exporter PCI card.

Shutdown Status

Output (Open/Ground)

Ground potential (0 V) when the Exporter Plus is shutting
down. Open circuit during normal operation.

Operational Status Output (Open/Ground)

Ground potential (0 V) when the Exporter Plus is operational

(

Status

LED is green or orange) . Open circuit when non-

operational.

Alarm Status

Output (Open/Ground)

Ground potential (0 V) when an alarm (

Status

LED red) or

warning (

Status

LED orange) is active. Open circuit when e

no active alarms or warnings. Along with pin 20, can

Common

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 54 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: