Nautel Exporter Plus Скачать руководство пользователя страница 97

Страница: 97 / 186

Exporter Plus Technical Instruction Manual

Operating

Issue 1.0 2020-05-05

Page 8-27

Figure 8.52: Ethernet 0 or 1 Netmask Editing Screen

Use the right and left buttons to highlight the desired digit in the new address, then use the up

and down buttons to change the value of the highlighted digit. Press the accept or cancel

button to enter the Save/Cancel screen (see

Figure 8.4 on page 8-5

). Save or cancel as desired.

Setting DNS server IP address

When you select

DNS Server IP

from the

NETWORK CONFIG

menu (see

Figure 8.55

) you can set

the IP address of the DNS server.

The IP address points to a domain name server, allowing for

host name resolution. If any network interface is set to DHCP, it is assumed that DHCP

provides the DNS server IP.

Figure 8.53: DNS Server Screen

To change the DNS server IP address, press the checkmark (accept) button to enter the editing

screen shown in

Figure 8.56

Figure 8.54: DNS Server Editing Screen

Use the right and left buttons to highlight the desired digit in the new address, then use the up

and down buttons to change the value of the highlighted digit. Press the accept or cancel

button to enter the Save/Cancel screen (see

Figure 8.4 on page 8-5

). Save or cancel as desired.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 97 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: