Nautel Exporter Plus Скачать руководство пользователя страница 167

Страница: 167 / 186

Exporter Plus Technical Instruction Manual

Troubleshooting

Issue 1.0 2020-05-05

Page 10-1

Section 10:

Troubleshooting

The fastest way to determine the Exporter Plus’s status is by viewing the front panel user

interface (UI). The

View Status

menu of the LCD display can assist in diagnosing a fault as well

as the four LEDs adjacent the display. When there are alarms, or the Exporter Plus is no longer

operational, these LEDs will turn red. The Exporter Plus also allows for continuous remote

monitoring via an Ethernet connection.

The features described above allow the user to determine the Exporter Plus’s operational status

at almost any time. In the event that the Exporter Plus becomes non-operational, some simple

troubleshooting procedures can be followed to return it to operational status. This section

outlines some common errors and warnings that may occur, along with the procedures to

correct each problem.

The following troubleshooting information is included in this section:

•

GPS related alarms - see page 10-2

•

Network related alarms - see page 10-3

•

System related alarms - see page 10-7

•

Importer related alarms - see page 10-7

•

LED indications - see page 10-8

•

Audio related alarms - see page 10-10

•

Checking cable connections - see page 10-11

•

Parts information - see page 10-12

• Electrical schematic - see page 10-13

Note: It is highly recommended that troubleshooting personnel be familiar with the

operation of the Exporter Plus. Refer to the Operating section of this manual as an

aid in troubleshooting.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 167 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: