Nautel Exporter Plus Скачать руководство пользователя страница 98

Страница: 98 / 186

Exporter Plus Technical Instruction Manual

Operating

Page 8-28

Issue 1.0 2020-05-05

Setting default gateway

When you select

Default Gateway

from the

NETWORK CONFIG

menu (see

Figure 8.55

) you can

set the default gateway address associated with the Ethernet ports.

The gateway can be

configured to use DHCP by setting its IP address to 0.0.0.0.

Figure 8.55: Default Gateway Screen

To change the default gateway address, press the checkmark (accept) button to enter the

editing screen shown in

Figure 8.56

Figure 8.56: Default Gateway Editing Screen

Use the right and left buttons to highlight the desired digit in the new address, then use the up

and down buttons to change the value of the highlighted digit. Press the accept or cancel

button to enter the Save/Cancel screen (see

Figure 8.4 on page 8-5

). Save or cancel as desired.

Enable/disable IP forwarding

When you select

Enable IP Forward

from the

NETWORK

menu (see

Figure 8.57

) you can enable

or disable IP forwarding. IP forwarding allows IP traffic received by the Exporter Plus on

either Ethernet port (but not destined for the Exporter Plus) to be copied to the other Ethernet

port.

Note: IP forwarding is only relevant if both Ethernet ports are in use. It is generally

recommended that you enable IP forwarding.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 98 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: