manualshive.com logo in svg

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 27 / 186

Поделиться
Скачать
Nautel Exporter Plus Скачать руководство пользователя страница 27

Exporter Plus Technical Instruction Manual

Parts and tools

Issue 1.0  2020-05-05

Page 3-1

Section 3:  

Parts and tools

This section describes parts associated with the HDMC+, and tools needed during installation 

and routine operation.

Parts supplied by Nautel

Ac power cable

An ac power cable is included with the HDMC+.

Documentation

This Technical Instruction Manual accompanies the HDMC+. Additionally, the 

documentation is provided online. 

See “Online resources” on page xi.

Parts not supplied by Nautel

Nautel does not supply some parts and materials required to complete installation. The parts 

you need vary with the installation requirements.

Tools for installation

The tools you need during HDMC+ installation include the following:

• Philips screwdrivers, sizes # 1 and # 2

Содержание Exporter Plus



























































































































































































Отзывы:

Нет отзывов