manualshive.com logo in svg

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 113 / 186

Поделиться
Скачать
Nautel Exporter Plus Скачать руководство пользователя страница 113

Exporter Plus Technical Instruction Manual

Operating

Issue 1.0  2020-05-05

Page 8-43

Figure 8.92: Audio Source Editing Screen

Use the up and down buttons to highlight the desired audio source (

Digital In

, 

Live Analog

, 

Delayed Analog

, 

Generated Tone

, 

Generated Pulse

 or 

RTP Stream In

).

 

You can adjust the 

volume of the signal applied to the headphone jack (see 

“Adjusting headphone volume” on 

page 8-43

). If you select 

Generated Tone

 or 

Generated Pulse 

as the audio source, you can also 

set the test tone frequency (see 

“Setting test tone frequency” on page 8-44

) and its left-right 

content (see 

“Setting test tone left-right content” on page 8-46

). Press the accept or cancel 

button to enter the Save/Cancel screen (see 

Figure 8.4 on page 8-5

). Save or cancel as desired.

Adjusting headphone volume

When you select 

Headphone Volume

 from the 

AUDIO MONITOR

 menu (see 

Figure 8.93

) you 

can adjust the volume of the audio source being monitored at the front panel headphone jack

.

Figure 8.93: Headphone Volume Screen

To adjust the headphone volume, press the checkmark (accept) button to enter the editing 

screen shown in 

Figure 8.94 on page 8-44

.

Содержание Exporter Plus



























































































































































































Отзывы:

Нет отзывов