Nautel Exporter Plus Скачать руководство пользователя страница 114

Страница: 114 / 186

Exporter Plus Technical Instruction Manual

Operating

Page 8-44

Issue 1.0 2020-05-05

Figure 8.94: Headphone Volume Editing Screen

Use the right and left buttons to highlight the desired digit in the new headphone volume

value, then use the up and down buttons to increase or decrease the value of the highlighted

digit. You can adjust the volume between 0 and 100%. Press the accept or cancel button to

enter the Save/Cancel screen (see

Figure 8.4 on page 8-5

). Save or cancel as desired.

Setting test tone frequency

When you select

Test Tone Frequency

from the

AUDIO MONITOR

menu (see

Figure 8.95

) you

can set the frequency of the internally generated test tone

Figure 8.95: Test Tone Frequency Screen

To adjust the test tone frequency, press the checkmark (accept) button to enter the editing

screen shown in

Figure 8.96

Figure 8.96: Test Tone Frequency Editing Screen

Use the right and left buttons to highlight the desired digit in the new test tone frequency, then

use the up and down buttons to increase or decrease the value of the highlighted digit. You can

adjust the test tone frequency between 50 Hz and 10,000 Hz. Press the accept or cancel button

to enter the Save/Cancel screen (see

Figure 8.4 on page 8-5

). Save or cancel as desired.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 114 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: