Nautel Exporter Plus Скачать руководство пользователя страница 41

Страница: 41 / 186

Exporter Plus Technical Instruction Manual

Quick setup procedure

Issue 1.0 2020-05-05

Page 6-3

Verifying operating mode

The operating mode of the Exporter Plus is typically set at the factory. Verify the operating

mode is set properly as follows:

Figure 6.2: Verifying Operating Mode

1. From the UI’s

Edit Settings - System Settings

page, select

Operating Mode

(see

Figure 6.2

2. Verify the operating mode is set correctly:

For AM operation, select

AM MA1

for hybrid operation or select

AM MA3

for all-digital

operation.

For FM operation, select

FM MP1-MP3

for typical hybrid operation or select

FM MP5

FM MP6

for all-digital operation

Note: The Exporter Plus will restart after a mode change.

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 41 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: